Air Showers->
Cleanroom Apparel->
Cleanroom-ESD-Lab Chairs->
Cleanroom-ESD-Lab Stools->
Cleanroom Clean Benches->
Cleanroom Cleaning Supplies->
Cleanroom Components->
Cleanroom Pass Thrus->
Cleanrooms->
Curtains & Strip Doors->
Desiccators - Stainless Steel->
Dispensers->
Documentation - Cleanroom->
Filters & Prefilters->
Flooring->
Fume Hoods & Glove Boxes->
Gloves & Finger Cots->
Gowning Room Components->
HEPA Cabinets & Casework->
Instrumentation - Cleanroom->
Mats - Tacky & Anti-Fatigue->
Packaging Products->
Safety Products->
Spray Guns
Static Control->
  Bags - Static Control
  Cleaners - Static Control
  Dispensers
  Flooring
  Garments
  Heel Grounders
  Instrumentation
  Ionizing Air Guns
  Ionizing Bars
  Ionizing Fans & Blowers
  Lotions
  Mats - Table / Floor
  Storage
  Tape
  Wrist Straps / Cords
Storage->
Swabs & Applicators->
Tape->
Ultrasonic Cleaning->
Ultraviolet Equipment
USP 797 - Compliance
Wafer Handling
Wet Process Station->
Wipes - Cleanroom->
Wire Shelving & Carts->
Workstations & Cleanroom Tables->
Featured Products
Specials
Manufacturers
Download PDF of this page  Print this page
Home » Static Control » Ionizing Bars » 4010550
 

$285.00

Air-Assist Pulsebar Tungsten

[4010550]

Air Assist PulseBar NEW DESIGN

The NEW AirAssist PulseBar features a special emitter pin configuration which significantly enhances the bar’s neutralizing and balance performance. The configuration includes an emitter pairing at each end to eliminate potential single polarity hot spots at either end of the bar, and increased emitter quantity in most sizes.

Emitter pins are now machined tungsten, not tungsten wire for greater durability and longevity.

The AirAssist PulseBar connects to compressed air lines and eliminates troublesome electrostatic charges that can cause dust and other contaminants to accumulate on surfaces and finished product. The flow of air over the electrodes carries the ionization to the surface to be neutralized. It can be mounted 2 to 3 feet from the target area and is available in standard lengths from 12 to 74 inches. Featuring a slimline design, the rugged AirAssist PulseBar can be installed on many types of equipment. It can operate in Steady State operating mode or Pulsed DC operating mode using the PulseFlow Controller. It is easily maintained.

REQUIRES EITHER PFC-20 or VisION controller.

Specification:
Size (W x H x D) - 0.95" x 1.2" x varied length (2.4 cm x 3.0 cm x length)
Cable Length - 7 ft. (2.1m)
Air Supply - 100 psi, clean dry air
Material - ABS plastic/anodized aluminum
Operating Temperature Range - 24 to 158 F (-10 to 70 C)
Air Inlet - 1/4" O.D. tube, push-in type


12" Air-Assist PulseBar with 7 Tungsten emitters - Part # 4010550 - $285.00
24" Air-Assist PulseBar with 7 Tungsten emitters - Part # 4010551 - $325.00
36" Air-Assist PulseBar with 11 Tungsten emitters - Part # 4010552 - $500.00
44" Air-Assist PulseBar with 15 Tungsten emitters - Part # 4010553 - $590.00
64" Air-Assist PulseBar with 19 Tungsten emitters - Part # 4010554 - $760.00
74" Air-Assist PulseBar with 19 Tungsten emitters - Part # 4010555 - $820.00



ACCESSORIES

PFC-20 PulseFlow Controller, 115V - Part # 4005184 - $390.00
VisION Controller - Part # 4008832 - $645.00
YQC 2-to-1 Air Quick Connector - Part # 5050540 - $13.00
HV2 2-to-1 connector (splitter) - Part # 5050538 - $60.00
HV4 4-to-1 connector (splitter) - Part # 5050539 - $70.00

 
 
 
  Quantity:
 
   
 

Home | About Us | Vendor List | Contact Us | Terms | Site Map
Secure Shopping | Customer Feedback
1045 10th Avenue SE • Minneapolis, MN 55414 • Tel: 612-827-6880 • Toll Free: 1-888-270-0458 • Fax: 612-827-0789 • E-mail: info@innotechprod.com
Site Credits: Ecreativeworks